Table of Contents
I. Operating Instructions
A. Caution Warnings Page 3.
B. Specifications 3.
1. CLEANING 4.
2. LUBRICATION. Where to oil the machine. 4.
3. HOW TO INSTALL THE NEEDLE 5.
4. HOW TO TAKE OUT THE BOBBIN 5.
5. HOW TO WIND A BOBBIN 5 and 31
6. HOW TO INSTALL THE BOBBIN 6.
7. HOW TO THREAD THE MACHINE 6 and 32
8. ADJUSTING THE STITCH LENGTH 7.
9. THREAD TENSION 7.
10. THE THREAD TAKE-UP SPRING 7.
11. ADJUSTING THE PRESSER FOOT PRESSURE 8.
12. FEED DOG ADJUSTMENT 8.
13. WALKING FOOT HEIGHT ADJUSTMENT 9.
14. SHUTTLE AND NEEDLE TIMING ADJUSTMENTS 9, 10, 11, 12.
15. FEED TIMING ADJUSTMENTS 12.
16. TROUBLE SHOOTING GUIDE 13.
II. Spare Parts List
1. FRAME AND COVER COMPONENTS 16.
2. MAIN SHAFT COMPONENTS 17.
3. NEEDLE BAR & UPPER FEED COMPONENTS 18, 19.
4. PRESSER BAR COMPONENTS 20, 21.
5. FEED MECHANISM 22, 23.
6. HOOK DRIVING SHAFT COMPONENTS 24, 25.
7. TENSION COMPONENTS 26, 27.
8. BOBBIN WINDER & THREAD GUIDE PARTS 28, 29.
9. KNEE LIFTER COMPONENTS 30.
2.
31.
1. Raise the presser foot with the hand lifter lever.
2. Insert the bobbin onto the bobbin winder spindle.
3. Thread the winder in the order illustrated and wind the
thread four or five turns onto the bobbin.
4. Push the bobbin winder trip latch (A) down. When the
machine is operated the spindle will turn and start to wind
the bobbin.
5. When the bobbin is fully wound, the trip latch will
disengage and the spindle will stop.
To adjust the quantity of thread on the bobbin:
1. Loosen the adjusting screw and nut number (B) and (C.)
and turn the screw counterclockwise to decrease the
amount of thread on the bobbin and clockwise to increase
the quantity of thread wound onto the bobbin.
2. Tighten the locking nut after adjusting for the correct
amount of thread to be wound onto each bobbin.
If the bobbin is not winding evenly, move the thread guide (D)
either left or right to compensate.
Several Bobbins can be wound while the machine is stitching.
Winding the Bobbin on a TORO-4000 R
TORO-3000 Bobbin Winder Instructions:
1. Place the bobbin on the spindle. Align the small pin with the hole
or slot in the bobbin.
2. Insert the thread into the eye above the bobbin winder tension.
3. Pull the thread around the and through the tension discs.
4. Continue pulling the thread to the bobbin and wrap several turns of
thread around the bobbin.
5. Push the Latch up against the center of the bobbin.
6. Operate the machine and the bobbin will begin to fill. Several bobbins can be
wound while the machine is in operation.
If the thread is wound too loosely, tighten the tension nut, if too tight, loosen the nut.
We Strive to Continuously Improve our Machinery. Specifications and features are constantly being updated.
Your New TORO Stitcher may look slightly different then as shown in this pamphlet.
(1 pages)
(16 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals